Table des matières

TNY-360 Documentation

Sourcing the components

In this section we will see how and where to get all the components, tools, screws, cables and other materials needed to build your TNY-360 robot from scratch.


Get the necessary tools

Before starting, ensure you have gathered all the necessary hardware and tools for the build.

ToolRecommendationLink [Option]
TS101AliExpress
-AliExpress
-AliExpress
-AliExpress
-AliExpress
MIJIA Electric ScrewdriverAliExpress
-AliExpress [5M / 10MM / 2MM]
-AliExpress
-AliExpress

*Only needed if you plan on soldering the PCB components yourself.


Order the Components

Here is a detailed list of all the components you will need, along with links to purchase them:

ComponentDescriptionQuantityLink [Option]
3W 4Ω Speaker (25mm x 35mm)1Aliexpress [3W 4Ω]
MG996R Metal High-torque servomotor for the legs12[180° Metal]
MG90D Metal Micro servomotor for the ears2[180° Metal]
Round metal horn for the MG996R servomotors12
Wi-Fi/Bluetooth 2.4Ghz antenna1Aliexpress [FPC-IPX1 / 10cm]
OV3660 120° 75mm FPC1Aliexpress [120 Degrees]
SSD1309 1.54" White OLED Screen 128x641Aliexpress [White 4pin]
20A Mini Automotive Fuse1Aliexpress [20A]
4x2mm Neodymium Magnets4Aliexpress [4x2mm]

Get the Screws and Cables

The TNY-360 uses a couple of M3 screws and heat inserts for assembly. Here's were to get them:

ItemDescriptionQuantityLink [Option]
M3 screws, 6mm in length50Aliexpress [M3 / 6mm]
M3 heat inserts, 4mm in length50Aliexpress [M3 (OD4.2mm) / 4mm]
10cm FPC cable, 8 pins, 1mm pitch1Aliexpress [1.0MM / 10CM / 8P]
10cm FPC cable, 14 pins, 1mm pitch1Aliexpress [1.0MM / 10CM / 14P]
JST-PHD Cable, 2x3 pins, 20cm length1Aliexpress [20cm / Reverse / 2x3P]
JST-SH Cable, 3 pins, 20cm length4Aliexpress [SH 1.0MM / 20cm / 3 Pin]
JST-PH Cable, 2 pins, 10cm length2Aliexpress [PH 2.0MM / 10cm / 2 Pin]
JST-PH Cable, 3 pins, 20cm length2Aliexpress [PH 2.0MM / 20cm / 3 Pin]
JST-PH Cable, 4 pins, 20cm length1Aliexpress [PH 2.0MM / 20cm / 4 Pin]
JST-XH Cable, 4 pins, 10cm length12Aliexpress [XH 2.54MM / 10cm / 4 Pin]
JST-XH Extension, 4 pins, 20cm length4Aliexpress [3S / 20CM / 5PCS]

Cable orientation

When ordering the cables, pay close attention to the orientation of the connectors.

The two ends of a cable can be connected in two ways:

  1. Same - the connectors on both ends have the same orientation (e.g. both with the latch facing up).
  2. Reversed - the connectors on both ends have opposite orientations (e.g. one with the latch facing up and the other with the latch facing down).

For the TNY-360 build, you will need ONLY REVERSED cables, because this orientation keeps the pin order consistent across all connectors (GND is always first).
DO NOT BUY SAME ORIENTATION CABLES, as this may cause short circuits and damage your components because you'll connect the pins in the wrong order (e.g. GND to VCC).