Table des matières

TNY-360 Documentation

Ordering the PCBs

The TNY-360 contains 10 custom PCBs, each serving a specific purpose in the robot's electronics architecture.

These PCBs have been designed to save space, simplify assembly, and to ensure a certain level of quality and reliability in the connections between components.


List of PCBs

You can find all design files (Gerber, BOM, PickAndPlace) in the GitHub repository.

Here's the list of all the PCBs you will need for this build :

PCBPurposeQuantityFiles
Exposes I2C pins and power rails for custom extensions.1GitHub Link
Takes the battery power and distributes it to the buck converter.1GitHub Link
Generates the signals needed to control the motors.1GitHub Link
Reads position feedback and contact switches signals.1GitHub Link
Measures the robot's orientation and motion.1GitHub Link
Detects contact between the robot's feet and the ground.4GitHub Link
The brain of the robot, hosts the main controller and other components.1GitHub Link
Contains the screen, laser sensor, and other front visor components.1GitHub Link
Acts as a bridge between all the boards and connectors of the robot.1GitHub Link
Converts the battery voltage to 5V and 6.7V for the rest of the system.1GitHub Link

Servo Feedback Boards

You'll also need to order 12x Servo Feedback Board to add position feedback to the motors, but these are not part of the TNY-360's electronics architecture.

In order to choose the right version of the Servo Feedback Board, please refer to the Choosing the right PCB section.


How to order the PCBs

Regardless of the manufacturer you choose, there's always a standard process to follow when ordering custom PCBs, with a couple of settings to specify to ensure the boards are fabricated correctly.

Here's what you need to know about the PCB ordering process and the recommended settings for the TNY-360 PCBs: PCB Files Preparation

For each of the 11 PCBs used in the TNY-360, you will find the design files in the GitHub Repository.

Each PCB folder contains these files :

  • Gerber
    These are the standard files required by PCB manufacturers to fabricate the boards. They include all the necessary layers (copper, silkscreen, solder mask, etc.) and drill information.
  • Bill of Materials
    A list of all the components needed for the PCB, including part numbers and recommended suppliers.
  • Pick and Place
    These files indicate the exact placement of components on the PCB, which can be used for automated assembly if supported by the manufacturer.

These files are standard and common for PCB manufacturing, and you should be able to upload them directly to the manufacturer's website when placing your order. If not, please contact us so that we can find a solution to ensure you can get the PCBs without any issues.

When placing your order with a PCB manufacturer, ensure you specify the following parameters to match the design requirements of the TNY-360 PCBs:

ParameterRecommendedDescription
Layers2Standard two-layer PCB for cost-effectiveness and sufficient functionality.
Board Thickness1.6mmStandard thickness for durability and mechanical stability.
Copper Weight1oz (35µm)Standard copper thickness for reliable electrical performance.
Solder Mask ColorBlack or GreenAesthetic choice. Green is more common and may be cheaper, while black can give a sleek look.
Silkscreen ColorWhiteProvides good contrast for component labels and markings.
Material TypeFR4Standard PCB material for reliability and performance.

Servo board thickness

Please use a thickness of 0.8mm for the Servo Board to ensure it fits properly within the MG996R servo casing.
Using a thicker board may cause fitting issues and could require modifications of the servo shell.

Buck Converter Layers

The Buck Converter PCB is a 4-layer board. Please double-check that the manufacturer supports 4-layer PCBs and specify this in your order to ensure proper fabrication.

Ordering the stencil

While most components on the PCBs aren't extremely small, we highly recommend ordering a solder paste stencil along with your PCBs if you plan on assembling the boards yourself.

A stencil will make the soldering process much easier and more precise.


How to order the PCBs components

We recommand ordering the PCBs already assembled by the manufacturer (PCB Assembly service) to save time and ensure a high-quality assembly, especially for the main board which has a high density of components and complex connectors.

But if you want to order the components separately and assemble the boards yourself, here's what you need to know :

The BOM files

Every PCB folder in the GitHub repository contains a Bill of Materials (BOM) file, which lists all the components needed for that specific PCB, along with their part numbers and other notes.

Use these BOM files to find and order the components from your preferred suppliers. You can use platforms like Mouser, Digi-Key or LCSC.

Matching components

The availability of components can vary based on your location, the supplier you choose, and the current market conditions. If you find that some components are out of stock or unavailable, here's how to find suitable alternatives:

  • Same footprint: Ensure that the alternative component has the same physical footprint as the original one, so it can fit on the PCB without requiring modifications.
  • Same specifications: Check that the electrical specifications (voltage, current, power rating, etc.) of the alternative component match those of the original to ensure proper functionality and safety.
  • Check the datasheet: Always refer to the component's datasheet to verify that the alternative meets all necessary requirements and is compatible with the design.

Ask the community

If you have trouble finding a specific component or need help finding a suitable alternative, don't hesitate to ask the community for help! You can talk to us via our Discord server or send us an email at contact@tny-robotics.com.